Malaysia 135LC Owners

"apa kebenda tah pasal cam"

Saved reading note:











Camshaft Basics and Terminology - Tilden Technologies
Understanding Camshaft Specifications - Lunati Power
Camshaft Selection - by Michael Ecker
Valve Timing Basics - Tech Center

Image Source: Google
Disclaimer: All images are copyright to their respective owners.



Degree Wheel

How do I find true crankshaft Top Dead Center (TDC)?
Camshaft Overlap on Top Dead Center (TDC)

Degree Wheel Printable Version
 
Degree Wheel Kit Image Example

Original Image Source Here
More Reading Here

Oncoming



Stuff
  • Cam Shaft CMS (T) ✔
  • Cam Shaft Bearing 6906 ✔
    Notes:
    Tappet valve clearance probably gonna be set around IN 0.08mm EX 0.10mm
    If applicable will and need to check with the degree wheel for overlap, lift and duration. (*adjustable timing gear)

  • Engine Oil
    Toyota Coolant ✔

  • Upper Cylinder Gasket ✔
    Lower Cylinder Gasket ✔
    Left & Right Engine Gasket



  • UMA Shark Adjustable Timing Gear ✔
    Notes:
    Upon request from the mechanic so it is applicable to advanced or retard the camshaft timing.
  • Manual Timing Chain Tensioner ✔
  • 6 Spring Clutch Housing
    Notes:
    Need more grip
  • Auto Clutch Shoe ✔
    Notes:
    "Wear & Tear" need to replace ASAP.

Headworks

Cylinder Head
Notes:
Cylinder head disassemble, ported and polish for intake and exhaust for less restricted flow to compensate the bigger piston.

Cylinder Block
Notes:
Need to double check the piston, piston rings and cylinder condition for scratches and defects.

Others:
Mileage Log at 23180 on odometer.

to be updated...

Pakej Kepala Valve Besar



Ok hari ni sembang² dengan kawan pasal head, ada terserempak head MDS valve 22/19 dengan harga RM280.00 Tak sempat nak confirm harga betul betul lagi dengan tuan punya badan. Jadi sesiapa yang berminat nak pakai valve besar boleh la hubungi saudara Akmar untuk pertanyaan yang lebih lanjut.

Head MDS
Pakej dapat:
cam racing mds
valve mds 19-22
spring valve cms
RM280
0103813775 - Akmar

Facebook Link Here - Akmar Motor Part

Future Disassemble



Considering these combination on next disassemble
  • Cylinder Head 22/19 valve, need to port and polish
  • 57mm Cylinder FZ150/Vixion
  • 57mm Dish type low compression piston need valve pocket
  • Cam CMS (T) tappet clearance In ? Out ?
    IN 0.08mm EX 0.10mm
  • CMS Valve Spring

To get:
New cylinder bottom gasket
New engine oil SAE 20/50
New Toyota coolant

Carburetor jetting range Pilotjet #35 Mainjet #110 - #115

Current:
15/37 112 chain link
80/90 front, 90/90 rear

On List:
New Auto Clutch Shoe
Capacitor Discharge Ignition (CDI)
6 Spring Clutch Housing
New Exhaust


57mm Vixion/FZ150 Pocket Valve Example

to be updated...
Image source: Google

The Jetting



Availabe size:
Pilotjet: #32.5 #35 #37.5 #42
Mainjet: #110 #138 #150 #155 #160

Currently on PJ #37.5 MJ #160 Needle at middle clip, 2 turn.
Default setting for the air screw is 1 turn out, max turn at 1 ¼, 1 ½ turn.

Notes:
  • Warm up your engine to the proper operating temperature. 
  • Turn the idle up so it is idling about 500 RPM’s higher than normal.
  • Turn the airscrew all the way in until it bottoms out, once bottomed out slowly back the screw out a ¼ turn at a time (give the engine 10-15 seconds between each ¼ turn of the screw, to allow the engine to catch up w ith the adjustments).
  • Continue backing the airscrew out until the engine idles at its highest RPM.
  • The preferred setting window is between 1 and 2 turns.
  • If the engine idles at its highest RP M from 0-1 turns out this mean s the pilot setting is on the Lean side and a larger pilot jet should be installed.
  • If the engine idles at its highest RPM at over 2 turns out, this means the pilot setting is on the Rich side and a smaller pilot jet should be installed.

Notes Original Source